js

mega nav

RECENT POSTS

7.10.11

7 Tutorial: Veneer Pendant Lights

Guest tutorial by Holly of The Adventures of an Almost 40 Year Old Intern
 

Today we're thrilled to have Holly of The Adventures of an Almost 40 Year Old Intern share with us her new tutorial on making veneer pendant lights!  Check her out on the Nate Berkus Show making her brass lights next week (in the U.S. on October 12th)!

Recently I visited one of my favorite stationery stores in town and saw these beautiful wooden sheets of paper; a thin veneer made from so many different types of wood (cherry, walnut, birds eye maple, aspen, red cedar, you name it!) and was really inspired by it.  I thought it would be perfect for creating a light fixture (clearly I am on a lighting kick lately!)  So, I made some (two of them to be exact) and I didn't think it was possible but I love these just as much as my brass pendant diy!

If you like what you see above, here are the directions on how to create your own:




Materials needed:
  • sheets of  11x17" two ply wooden paper (for the smaller lamp i used 1 sheet of birds eye maple and 1 of red cedar and 1 of walnut and for the larger i used 3 1/2 sheets of the cherry)
  • 2 embroidery rings
  • 1 piece of basswood measuring 1/16" x 4" x 24"
  •  glue (E-6000 is my favorite)
  •  bulldog clips (i used both size 0 and 1)
  • x-acto knife (i used size #2)
  • pencil
  • measuring tape
  • long ruler or straight edge to cut against
  • pendant light 
Larger Pendant

Start with two embroidery hoops, one measuring 12" diameter and the other 5" diameter (I only used the fully formed hoop and did not use the outer hoop with the metal hardware attached).  Cut 4 pieces of the paper measuring 1" wide and 11" long.  Measure the hoops and divide them into 4 equal parts and and mark each. then attach each piece of the wood strip to the top and bottom with glue and cover each end with bulldog clips until it sets


While that part is drying cut 1" strips of paper that are each 17" long.  Note: I was careful to keep them in order because I wanted the wood grain to match when i glued them.


Begin attaching the wooden paper to the large hoop first. as you attach them, line them up with the top of the hoop, clip the outside of each piece in order to hold it. note: i ended up buying and using a bunch more clips than I started with in order to be more efficient with my time.


After finishing with the large hoop, move on to attaching each end to the smaller one. Note: here I had to overlap the strips of paper in order for it to fit onto the smaller hoop. I was careful to keep the grain lined up.


Once dry, use a 17" long 1" wide strip of paper to wrap around the outside of the smaller hoop to cover glue and seams and use two 17" strips to wrap around the outside of the larger hoop.  To create the piece that will hold your pendant, trace the inside and outside of your smaller hoop onto a piece of basswood. Use your straight edge to draw a line from the inner hoop tracing from corner to corner to find the center of the piece. This is where you will draw a circle large enough to thread your pendant wire through (should be big enough to allow the plug to pass through).


Cut where you traced the outside edge of your hoop as well as the circle in the center .  Slide the piece into the top of your fixture from the bottom.  You shouldn't need glue as it will be stable with your paper strips holding it.

Smaller Pendant

The directions are the same but instead of using a large and a small hoop, I used 2 small hoops. Also instead of using one type of wooden paper i used 2; instead of 1" strips that were 17" long I cut 1 1/2" strips;  and I used 2 short braces instead of 4.

For these lights I am using a super duper low wattage bulb. I did order fire retardant spray to apply to them as a precaution but it didn't arrive in time for this post so I don't know if it will affect the wood.


For those of you just tuning in and wanting to know more about Holly  you can by going here and online:

facebook 
twitter

7 comments:

Katie said...

Those are beautiful and seem relatively easy to make. Thanks for sharing!!

katie [the bright life] said...

These are so cool! I'm feeling very inspired...love the wood grain look! Xo, Katie

Momichka said...

Lovely lights. Remind me of the Christmas decorations we used to create as kids.

These would look great if made from paper,too.

*SABA*(FrWaH) said...

that's soooo beautiful and now seems easy to try..i want to know how to make a chinese lantern too..

vosges paris said...

I could really use some of these ideas for my own project thank you so much for sharing

janmadeit said...

I knew there was a reason to be hoarding embroidery hoops! Can't wait to get some veneer to play with!

Sonneman said...

Fabulous lamps! Nice work! Thanks for doing this blog. I absolutely love it! Get more information about Pendant Lights